SCSI命令中止,如何解决？

huaxiong_li

1# NeroAPI 版本 7.10.1.0
2# NeroAPI 初始化成功.
2# 刻录机: PIONEER  DVR-213N        
2# 写入速度: 8X (11080 KB/s)
3# 使用 DVD-R/RW,DVD+R/RW 或 DVD-RAM 光盘.
3# 写入速度: 8X (11080 KB/s)
4# 光盘介质: DVD-R
5# 文件暂存过程开始
6# 文件暂存过程完成
7# 以8x (11,080 KB/s)的速度开始刻录
8# 写入简短的引出
9# SCSI命令中止
9# H: PIONEER DVR-213N
10# 无法进行光盘一次刻录的结束动作
11# 以8x (11,080 KB/s)的速度刻录失败

1）今天刻录DVD视频；TDA打包OK后；
2）开始用Nero刻录；（威宝的碟子刻飞2张；后来用TDK的刻飞1张）
3）再次将视频文件用UltraISO打包成ISO文件，用UltraISO再次刻录TDK的碟子，又刻飞了，
     显示的信息如上面的所示： SCSI命令中止；{:soso_e141:}
想请问大家有没有遇到过这样的事情？怎么去解决？

huaxiong_li

还有补充一点，我这两天有将CPU超频：2.0GHz超频至2.3GHz；
超频应该不会影响刻录吧；{:soso_e141:}

IsaacZ

想起什么就测试什么。

点拨论坛搜索：011  出错

huaxiong_li

不好意思；来晚了；
问题已经解决；
其实碟子并没有刻飞---后来确认碟子是可以继续刻录的（请大家不要当垃圾扔掉啦）；解决的方案------系统出了问题，重新装一次就OK；
简单吧！

cyberian

我的是刻录到1%的时候出现：写入简短的引出，之后光盘空白的，没刻过一样。也是系统问题？

伤心的笔

huaxiong_li 发表于 2011-8-22 20:10

                               
登录/注册后可看大图

不好意思；来晚了；
问题已经解决；
其实碟子并没有刻飞---后来确认碟子是可以继续刻录的（请大家不要当垃 ...

重装系统只是解决办法，这个问题的根源没有找到，就很难避免类似的事情发生。

伤心的笔

huaxiong_li 发表于 2011-8-22 20:10

                               
登录/注册后可看大图

不好意思；来晚了；
问题已经解决；
其实碟子并没有刻飞---后来确认碟子是可以继续刻录的（请大家不要当垃 ...

“碟子并没有刻飞”——因为刻录只是导出区没有写上，也就是结束光盘的操作没有完成，当然可以再写了

cyberian

伤心的笔 发表于 2012-7-16 11:02

                               
登录/注册后可看大图

“碟子并没有刻飞”——因为刻录只是导出区没有写上，也就是结束光盘的操作没有完成，当然可以再写了

12:52:19        #37 SPTI -1135 File SCSIPassThrough.cpp, Line 214
        CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135)
        CDB Data:   0x5C 00 00 00 00 00 00 00 0C 00 00 00
        Sense Key:  0x03 (KEY_MEDIUM_ERROR)
        Sense Code: 0x0C
        Sense Qual: 0x00
        Sense Area: 0x71 00 03 00 00 00 00 0A 32 4D 03 0C 0C
        Buffer x0c485dc0: Len xc
       
12:52:19        #38 SPTI -1064 File SCSIPassThrough.cpp, Line 214
        CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1064)
        CDB Data:   0x2A 00 00 00 00 20 00 00 20 00 00 00
        Sense Key:  0x05 (KEY_ILLEGAL_REQUEST)
        Sense Code: 0x21
        Sense Qual: 0x02
        Sense Area: 0x70 00 05 00 00 00 00 0A 2A 00 00 0C 21 02
        Buffer x190c0080: Len x10000
        0x30 00 D5 98 0D 00 00 0D 98 D5 FE 5F 14 00 00 14
        0x5F FE 6B 0A 18 10 39 00 20 00 00 00 01 00 00 01
        0x0E 5F 5F 5F 57 37 39 5F 5F 2E 45 58 45 3B 31 00


出现了这两个错误。准备再找找原因，不行的话重装系统看下可不可以解决。现用win7 x86的系统。

IsaacZ

cyberian 发表于 2012-7-16 13:40

                               
登录/注册后可看大图

12:52:19        #37 SPTI -1135 File SCSIPassThrough.cpp, Line 214
        CdRom0: SCSIStatus(x02) WinError(0) N ...

【光盘刻录错误代码查询】List of ATAPI Error codes 【NERO日志告诉我们什么】

cyberian

IsaacZ 发表于 2012-7-16 17:06

                               
登录/注册后可看大图

【光盘刻录错误代码查询】List of ATAPI Error codes 【NERO日志告诉我们什么】

对过了，傍晚回来刻录又出现新的问题write error。。

log是
18:59:06        #24 SPTI -1135 File SCSIPassThrough.cpp, Line 214
        CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135)
        CDB Data:   0x2A 00 00 00 00 00 00 00 20 00 00 00
        Sense Key:  0x03 (KEY_MEDIUM_ERROR)
        Sense Code: 0x0C
        Sense Qual: 0x00
        Sense Area: 0x70 00 03 00 00 00 00 0A 32 4D 03 0C 0C
        Buffer x190b0040: Len x10000
        0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
        0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
        0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
       
18:59:06        #25 CDR -1135 File Writer.cpp, Line 306
        Write error
        G: HL-DT-ST DVDRAM GSA-T40N

核对了http://www.cdr-zone.com/articles/atapi_error_codes_page_1.html地址的

也是**030C00    4 5 6 Write error

显示Write error  我迷茫了。

4. DMA Settings
Setting DMA mode:

Windows 95/98/ME Users

Right click on [My Computer] and select [Properties] from the menu. Click on [Device Manager], then click on [CD-ROM]. This will expand to show the CD drives on your system. Right click on a drive and select [Properties] from the menu. Click on the [Settings] tab and check that the [DMA] option is enabled. Repeat this procedure for the remaining CD drives.

Win NT/2000/XP Users

Right click on [My Computer] and select [Properties] from the menu. Click [Device Manager] on the [Hardware] tab, then click to open the [IDE ATA/ATAPI (hard disk) controllers] section. You will find: the Primary IDE Channel controller, Secondary IDE Channel controller. Complete the following procedure:

Right click on the Primary IDE controller and select [Properties] from the menu.
Select the [Advanced Settings] tab. Check that the [Transfer Mode] for both devices is set to [DMA if available].
Repeat this for Secondary IDE controller.


Note: In some cases older CD-ROM drives will not support DMA mode. In that case please set both devices to PIO mode.





5. Disc



Recording errors often occur when the disc is dirty, or has fingerprints or scratches. If an error occurred during test simulation (before actual recording), clean the disc. If you are getting recording errors, try the following.
Use a different blank, recordable disc.
Use a different manufacturer's disc.
Ensure the disc is clean before recording:
Remove all fingerprints, dirt, and dust from the shiny side of your disc using a nonabrasive cloth with a mild, nonabrasive soap solution.
Wipe the disc from the center to the edge of the disc.
Dry the disc completely.


Error during file verification
If an error occurred when the files were being verified, record the same files again using a different disc.


Read error when copying a disc
When copying a disc, if an error occurred while reading data from the original disc, the original disc may be scratched or dirty.
Try cleaning the disc.
Remove all fingerprints, dirt, and dust from the shiny side of your disc using a nonabrasive cloth with a mild, nonabrasive soap solution.
Wipe the disc from the center to the edge of the disc.
Dry the disc completely.
Try using a different source drive.
To change the drive you use to read your disc, click the Change button when asked to insert a source disc into your drive tray.
Select the drive you wish to use from the drop-down menu.
Insert your disc into the new drive.
Try using copying the disc using one drive as both the source and destination drive.
When you use your recorder to both read and write to your disc, B's Recorder GOLD creates an image file of the entire disc to your hard drive and then copies that temporary file onto your blank disc. This can be helpful if the drive you are using to read your original disc is slow or unreliable.

If the problem persists, contact the drive maker.





6. Drive
If you have tried Actions 1 through 5 above, there may be a problem with your drive. Contact the drive maker with details of the error code. If the 5th and 6th digit of the error code is 80 through FF, then the error code is maker unique. The descriptions of these error codes differ depending on the maker.

都试过去依然是写错误。会不会是现在换成 win7 的问题。以前用xp同样的威宝dvd-r刻录正常。
刻了20片没一片坏的。